Covid-19 - Merci de prioriser le courriel au lieu du téléphone pour nous contacter: MTL: Internet:
Notez que compte-tenu nos effectifs réduits ainsi que des transporteurs, les délais de livraison peuvent être plus longs. Vous pouvez également nous contacter sur notre page Facebook.

Plus de vues

599 $

Disponibilité Commande spéciale

Numark Scratch - 2-Channel Scratch Mixer for Serato DJ Pro


The Numark Scratch is a two-channel DJ mixer designed for use with the included Serato DJ Pro software. The mixer features a built-in InnoFADER crossfader, performance pads, instant loop encoder, and toggle paddles to trigger software-based effects. Also included is the Serato DVS expansion pack, allowing for immediate access to connector turntables or CD/media players and control of Serato DJ Pro using optional Noisemap Control Vinyl or CDs.

Six direct-access software FX buttons deliver quick access to a comprehensive array of effects with both timing and intensity controls. These effects are triggered by a pair of intuitive performance-based toggle paddles, while the instant loop encoder simplifies looping by pressing down on the encoder while turning to the right to extend the beat and turning left to shorten the loop.

The Scratch offers 32-bit fixed point DSP and 24-bit digital sound quality, plus a dedicated low-/high-pass filter that is not software dependent, making it available at any time with any source material including vinyl records. Each channel offers four performance pads for triggering hot cues, rolls, and samples. The rear panel offers stereo RCA inputs for each channel (line/phono switchable), stereo XLR master outputs, stereo RCA master outputs, and stereo RCA booth outputs. A combo XLR-1/4" microphone input is also included with a dedicated mic level control. The Numark Scratch Mixer ships with a power cord, a Prime Loop sound pack, and a 2-month subscription to SoundSwitch lighting control software.

  • Serato DJ Pro with DVS license included
  • Ready to connect to Serato NoiseMap Control Vinyl or CDs (available separately)
  • InnoFADER scratch crossfader with reverse and slope control
  • Six direct access effect selectors with dual-paddle launch triggers and dry/wet FX control
  • Eight performance pads to access hot cues, rolls, and samples
  • Filter knobs to create audio sweeps
  • Dedicated instant looping knobs
  • Phono/line inputs
  • Combo mic input (XLR/1/4") with level and tone control
  • 24-bit digital sound quality
  • Balanced high output XLR connection
  • Separate booth/zone output
  • Dual-headphone output cueing system (1/4" and 3.5mm)
  • Prime Loop sound pack included
  • SoundSwitch lighting control software included (2-month subscription)

Spécifications techniques

Connectors Inputs:
Channel 1: 1 x Stereo RCA (Phono/Line Switch)
Channel 2: 1 x Stereo RCA (Phono/Line Switch)
Microphone: Combo XLR-1/4" / 6.35 mm

Master (Balanced): 2 x XLR
Master (Unbalanced): Stereo RCA
RCA Booth: Stereo RCA
Master Output Balanced XLR Output Frequency Response: 20 Hz to 20 kHz (+0.2 dB)
Signal-to-Noise Ratio: 108 dB (A-Weighted, Max Output)
THD+N: 0.007% (1 kHz, -1 dBFS)
Maximum Output Level: +20 dBu
Output Impedance: 300 Ohms
RCA Outputs Master and Booth Outputs
Frequency Response: 20 Hz to 20 kHz (+0.2 dB)
Signal-to-Noise Ratio: 107 dB (A-Weighted, Max Output)
THD+N: 0.005% (1 kHz, -1 dBFS)
Maximum Output Level: +6 dBV (2 Vrms)
Output Impedance: 300 Ohms
Headphone Output 1/4 and 1/8" TRS
Frequency Response: 20 Hz to 20 kHz (+0.2 dB)
Signal-to-Noise Ratio: 108 dB (A-Weighted, Max Output, Unloaded)
THD+N: 0.005% (1 kHz, 10 mW per Channel into 32 Ohms)
Maximum Output Level: +14 dBu (Unloaded)
Power Output: 115 mW RMS (per Channel into 32 Ohms)
Output Impedance: 32 Ohms
Line Inputs RCA
Frequency Response: 20 Hz to 20 kHz (+0.3 dB)
Signal-to-Noise Ratio
102 dB (A-Weighted, Max Input Level)
THD+N: 0.008% (1 kHz, +6.8 dBV, -1 dBFS)
Max Input Level: +7.8 dBV (2.45 Vrms)
Input Impedance: 47 kOhms
Phono Inputs RCA
Frequency Response: RIAA Curve
Signal-to-Noise Ratio: 99 dB (A-Weighted, Max Input Level)
THD+N: 0.01% (1 kHz, -3 dB Input)
USB USB 2.0 High Speed
AD/DA Conversion 24-Bit, 48 kHz
DSP 32-Bit Fixed Point
Drivers PC: ASIO and Windows Audio
Mac: UAC2 Class Compliant (No Additional Driver Needed)
Power Input Typical: 120/240 VAC, 50/60 Hz Auto-Switching

Mots clés du produit

Utilisez un espace pour separer les mots clés. Utilisez l'apostrophe (') pour rédiger une phrase.

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now